Drilling units

The support can be equipped with two different drill units. Here the drills are always guided in a turret drill bush directly on the part.

Swivelling drilling unit

The swivelling drilling unit enables precise side drilling up to an angle of 45°.

• max. angle 45°
• max. drill length 650 mm for 650 mm version
• max. drill length 830 mm for 830 mm version

Deep hole drilling device

For through holes for up to 1,300 mm part width.

Standard slot cutter

Slot chains in various sizes can be mounted on this unit. Machining can take place on 4 sides of the part. Likewise, hidden slots are possible.

Guided slot cutter

During through slotting, the bar is fully automatic fixed on the operator side and the wood is accordingly moved continuously in longitudinal direction, which minimizes the operating time. Even hidden slots as well as the piercing operation are possible as before.

Marker

With the marker, diagonal marks and letterings can be made on the stop side of the part.

Inkjet marking system

With the inkjet marking system, the parts are automatically marked with the information stored in the SPCP.

Drilling units

The drills are guided in a turret drill bushing directly under the part. A higher-capacity drive unit with hydro-pneumatic feed is available for larger drill diameters.

End mill

Equipped with an end mill and a slot drill, the milling unit operating from below can complete all milling work such as mortises, holes, countersinks, ring dowels, profiles, etc.

Vertical turret mill

The vertical turret mill has 4 tool holders. Machining can be done on the end face, as well as on sides 1 and 3 of the part.
In connection with the vertical end mill, a synchronous motion is possible for simultaneously machining 2 sides of the part.

Top end mill

It is possible to machine the part on its side 1 using the top end mill. According to the diameter and length of the built in end mill all operations such as clogging, mortises, holes, longitudinal milling, as well as blocking groove are possible.

Longitudinal and cross groove mill

The angled longitudinal and cross groove mill (0 - 180°) allows blocking and longitudinal grooves to be made efficiently at any angle.

Horizontal turret mill

The turret head mill has four tool holders. The mill can be revolved in full 360°. Machining can be done on the end face, as well as on sides 2 and 4 of the part. It can also be used for oblique holes or cloggings

Horizontal saw

With the horizontal saw, it is possible to work on 4 sides of the part, on sides 2 and 4 as well as the two end faces. Clean slots up to 300 mm deep can be machined quickly with the large horizontal saw. If slots up to 145 mm deep are sufficient, even the combi-support can be equipped with a corresponding unit with saw blade.

Universal slot cutter 360°

With this side slot cutter, slots can be made on sides 2 + 4 of the part as well as on the end faces. The chain lubrication is fully automatic. The angle adjustment can be rotated through 360°.

Vertical slot cutter 

The slot cutter in vertical mounting direction was developed for special applications. Thus the vertical slot cutter can be used, e.g., in log house construction for window cut-outs.

Pivoting deep hole drilling unit

The swivelling deep hole drilling unit can be rotated through a full 360° and can machine the parts from all 4 sides.

Double support

For corresponding operations, the double support offers a substantial time saving, since it is possible to machine on two different sides of the part at the same time (synchronously). For synchronous motion, the tools on opposite sides must be identical. The double support can be equipped with a maximum of three drilling and/or milling units.

Log home unit

Consisting of 2 vertical and 2 horizontal mills for 4-axis rabbeting of log house planks. Two milling operations can be carried out simultaneously from opposite directions. Horizontal as well as vertical. The 4 mills can, however, function separately independently of each other and can be be set to the desired milling depth thus it is also possible to rabbet on one, two or three sides. The mills can be customized. The stroke is effected hydraulically.

Additional screen at part discharge point

An additional screen can be installed above the part discharge point. The fully machined parts are displayed here.

Part removal hood

The wood removal hood in front of the saw makes it possible to remove short parts without any stoppages. Short parts are conveyed in the direction of the collection attachment of the cover by the ejector and can be removed outside the machine zone without stopping the machine.

Dimensional measurement

With this unit, the dimension (width and height) is checked automatically for the timber cross-section. If deviations outside the selected tolerance (can be set in machine data) are determined, the machine stops and the cross-section deviation is displayed. In the case of cross-section deviations within the specified tolerance, the part is processed with the determined tolerance. Thus accurate machining is achieved without manual cross-section correction.
Because a reference side (joinery side) can be assigned, the part is automatically turned if it is wrongly positioned (upright or lying). The advantage is that

e.g. tenons are always exactly centred on the part.

Label printer

Printer on the operating desk for labels with various, freely selectable details such as, e.g., company name, part name, part number, cut grades or roof side. Data can also be imported from joinery and CAD programs.